Cont

Have any Questions?

+86 18626835909

May 11, 2022 View:

A Variety Of Bearing Installation And Use Instructions Introduced

Bearings as an important part of contemporary machinery, the application is more widespread. Generally in the selection of bearings are used according to its working conditions to choose different types of bearings, in order to better play the function of the bearing, and to extend the service life of the bearing. Today Ace lobe pump will take you to understand the installation and use instructions of various bearings.

I. Instructions for the mounting and use of rolling bearings

1、The bearing should be installed with even force, not directly hammered. Such as: with a large interference, the bearing should be placed in an automatic temperature-controlled air heating furnace or oil furnace, heating temperature is strictly controlled at 120 below.

2、The bearings equipped with nylon cage can work continuously and stably for a long time under -40-120, and should not work for more than 4 hours at 150, with a brief temperature peak up to 180.

3、The warehouse where the bearings are stored should be clean, dry and not allowed to be stored with chemical products, the relative humidity should not exceed 65%, and the bearings are not allowed to be stored on the ground.

Second, the installation of deep groove ball bearings instructions for use

1、The bearing should be installed with even force, not directly hammered. Such as: with a large interference, the bearing should be placed in an automatic temperature-controlled air heating furnace or oil furnace, heating temperature is strictly controlled at 120 below.

2、The bearings equipped with nylon cage can work continuously and stably for a long time under -40-120, and should not work for more than 4 hours at 150, and the brief temperature peak should not exceed 180.

3、The warehouse where the bearings are stored should be clean, dry and not allowed to be stored with chemical products, the relative humidity should not exceed 65%, and the bearings are not allowed to be stored on the ground.

4、Stock bearings should be cleaned again every other year and packed for rust prevention.

Three, the angular contact ball bearing installation use instructions

1、The bearing should be installed with even force, not directly hammered. Such as: with a large interference, the bearing should be placed in an automatic temperature-controlled air heating furnace or oil furnace, heating temperature is strictly controlled below 100.

2、The bearings equipped with nylon cage can work continuously and stably for a long time under -40-120, and should not work for more than 4 hours at 150, with a brief temperature peak up to 180.

3、The warehouse where the bearings are stored should be clean, dry and not allowed to be stored with chemical products, the relative humidity should not exceed 65%, and the bearings are not allowed to be stored on the ground.

Fourth, the installation of spherical roller bearings instructions for use

1、Users should choose the appropriate fit and bearing clearance according to the use requirements. After unpacking, please check the bearing code first.

2, in the bearing before installation, if you need to add grease in the bearing, grease must be clean, appropriate amount.

3, installation to not directly hammer the inner, outer ring end face and rollers as appropriate, so as not to crack the inner ring or in, small retaining edge. Usually the user should put the bearing into the mineral oil heated to 90-100 when immediately installed on the spindle. Do not use partial spray burning method for bearings, in difficult to heat installation when the user should also use special sleeve installation.

4、The bearings should have good sealing and dustproof device and lubrication in use, and the oil should not be broken.

5、The bearing warehouse should be clean and dry, no environmental pollution, the bearing pile does not fall to the ground, the packaging is not broken. Bearings in stock for more than 1 year must be cleaned and oiled again.

Five, the installation of thrust spherical roller bearings instructions for use

1、The bearing oil seal should be washed and then coated with clean and high quality lubricant when installing the bearing.

2、When installing the bearing, it should be evenly stressed and should not be hammered. If the fit interference is large, the bearing should be put into mineral oil and heated to 90-100, then immediately installed.

3、The warehouse where the bearings are stored should be clean, clean, with relative humidity not exceeding 65%.

4、The stock bearing should be cleaned and oiled again every one year, and the oil seal package should be kept in good condition.

5、When using bearings, there should be a good sealing and dustproof device, and the working condition should be checked frequently.

Six, cylindrical roller bearing installation and use instructions

1、The bearing is separated type, the user can adjust the clearance according to the need when installing.

2、Before use, the bearings should be cleaned with petrol or paraffin and kept well lubricated.

3、When mounting the bearing, press the bearing into the part, knocking is strictly prohibited.

4、The bearing storage place should be clean and ventilated to avoid moisture, and the bearings that need long-term storage should be rust-proofed regularly.

Seven, the installation of thrust ball bearings instructions for use

1、The bearing seal should be removed when installing the bearing, washed and then coated with clean and high quality lubricant.

2、When installing the bearing, it should be evenly stressed and should not be hammered. If the fit interference is large, the bearing should be put into mineral oil and heated to 90-100, then immediately installed.

3、The warehouse where the bearings are stored should be clean, clean, with relative humidity not exceeding 65%.

4、The stock bearing should be cleaned and oiled again every one year, and the oil seal package should be kept in good condition.

5、When using bearings, there should be a good sealing and dustproof device, and the working condition should be checked frequently.